Flooded Suction Sewage Pump Station


Flooded suction sewage pump stations offer the Design Engineer the most in custom features available today. These features include as standard, many items that are optional with other manufacturers. A broad list of optional equipment is available, as well as many different chamber and piping configurations.


Standard Equipment

  • Access tube with fiberglass cover and ladder
  • Ventilation blower & heater
  • Steel Chambers (various sizes)
  • Vertical flexible coupled non-clog sewage pumps
  • Filtered discharge water seal system
  • Ductile iron piping with bronze fitted valves
  • Liquid level control system
  • Dehumidifier
  • Lighting
  • Sump pump
  • Corrosion protection system
  • Power & control panel
  • Rubber floor mat
  • Epoxy painting system
Flooded Suction Sewage Pump

 

 

Vacuum Primed Sewage Pump Station


A Dakota Pump Inc. wet well mounted vacuum primed sewage pump station is the Design Engineer's choice with low cost, ease of installation, and maximum service-ability are the primary design factors. Dakota Pump Inc's. products are based on time proven equipment while keeping up with the latest in technological advances.

Unlike some manufacturers, Dakota Pump Inc. can offer many of the same options available on its line of flooded suction pump stations. Each pump station is individually designed for a particular set of design conditions, not modified to accommodate them. As with all Dakota Pump Inc. package pump stations, the Design Engineer has the ability to specify most nationally known pump and major component manufacturers, utilizing local sources of parts and service.

Wet Well Mounted Vacuum Primed Sewage Pump Station

 

Standard Equipment

  • Molded fiberglass enclosure
  • Internal conduit and wiring
  • Vertical non-clog sewage pumps
  • Steel piping with valves
  • Ventilation blower & heater
  • Vacuum priming system
  • Power & control panel
  • Mercury float switch level controls
  • Reinforced welded steel base with wet well access
  • Epoxy painting system

 

 

Self-Priming Sewage Pump Station


Dakota Pump Inc. self-priming sewage pump stations give the Design Engineer the choice to either bury the pump station to a flooded suction elevation, partially bury the station, or mount the station on the wet well. Custom features are almost limitless, with standard features including many items that are optional with other manufacturers.



Standard Equipment

  • Access tube with fiberglass cover and ladder
  • Ventilation blower & heater
  • Steel chambers (various sizes)
  • Lighting
  • Horizontal self-priming, non-clog sewage pumps
  • Corrosion protection system
  • Ductile iron piping with bronze fitted valves
  • Power & control panel
  • Liquid level control system
  • Dehumidifier
  • Manual air release system
  • Sump Pump
  • Rubber floor mat
  • Epoxy painting system
  • Internal conduit & wiring
Self-Priming Sewage Pump Station

 

 

Pneumatic Ejector Sewage Lift Station

Efficiency at low flows and low to medium heads is the best reason to specify Dakota Pump Inc. pneumatic ejector sewage lift stations. They offer the Design Engineer satisfactory solutions to some very difficult pumping conditions. Most often, a pumping condition that would fall on the extreme left hand side of a typical pump curve, can be met more efficiently and less costly by a Dakota Pump Inc. pneumatic ejector station.

Dakota Pump Inc. features include as standard, many items that are optional with other manufacturers. A broad list of optional equipment, as well as many different chamber and piping configurations, is available. Every Dakota Pump Inc. package pneumatic ejector sewage lift station is custom built to a particular set of design requirements, not modified to accommodate them. Dakota Pump Inc. offers the Design Engineer the ability to specify most nationally know brands of pumps and major components, thus utilizing local sources of parts and service.

Pneumatic Ejector Sewage Lift Station

 

Standard Equipment

  • Access tube with fiber glass cover and ladder
  • Ventilation blower & heater
  • Steel chambers (various sized)
  • Lighting
  • Air compressors
  • Air piping & valves
  • Ejector pots
  • Sump pump
  • Ductile iron piping with gate and swing check valves
  • Power & control panel
  • Control by a float switch mounted in each ejector pot
  • Dehumidifier
  • Corrosion protection system
  • Rubber floor mat
  • Epoxy painting system
  • Internal conduit & wiring